PRO-36 Auto | Auto Feed Mag Drill With Led Monitoring System

PRO-36 AUTO

New PRO-36 AUTO is equipped with unique LED monitoring system that indicates current condition of the drill and gives additional safety and diagnostic information.

 

Core drill
max 36 mm
(1-7/16”)
Depth of cut
51 mm
(2”)
Stroke
70 mm
(2-3/4”)
Speed
350 rpm
Power
1020 W
Weight
13.5 kg
(30 lbs)
Overload
protection
Magnet
detachment
safeguard

PRO-36 AUTO | Auto Feed Mag Drill

Auto Feed Smart Drive System optimizes parameters for each cutting/milling operation, when drill works in automatic mode. The drill controller keeps choosing the most effective working conditions based on the correlation of motor load, feed speed and the range of allowable cutting parameters for a given tool type and hole diameter. It results in extending tool life of both HSS and TCT cutters and enhanced machine performance. Twist drilling and countersinking operations as well as working on thin workpieces, when the LED shows that the clamping force is low (flashing green) are possible in manual mode only. A safety strap protects the machine from falling in case of a clamping loss.

  • LED Monitoring System indicates current condition of the drill and gives safety and diagnostic information
  • LED Monitoring System flashes green when inadequate adhesion is detected due to e.g. gap or thin workpiece
  • Auto Feed Smart Drive optimizes the milling parameters for each tool individually depending on its type (HSS or TCT) and hole diameter from 12 mm up to 36 mm, that significantly extends tool life
  • Tilt sensor stops the motor in machine breaks away
  • Dual bars guide system ensures extraordinary stiffness and adjustment free operation
  • Magnetic Field Shape Control (MFSC) provides maximum holding power on thin materials
  • Auto-feed control stops the machine when cutter goes through
  • Protection against auto restart after power cut off
  • Compact, rigid design with ultra-lightweight of 13.5 kg

Auto Feed Smart Drive optimizes the milling parameters for each tool type and hole diameter.

Auto-feed control stops the machine when the cuter goes through.

Dual bar guide system ensures long lasting frame stiffness and adjustment free slide.

LED Monitoring System

This unique LED interface generates signals in green and red colors to indicate current condition of the drill and give safety and diagnostic information. This new LED indicating light provides valuable information for the operator concerning current machine work mode and safety information.

Condition Of The DrillStrong surface. Ready to Operate.
(Solid Green)
Emergency stop. The base is not in contact with surface.
(3 Red Flashes between Green)
Emergency stop. Machine tilt or vibrations.
(4 Red Flashes between Green)
Emergency stop. Spindle motor overload.
(5 Red Flashes between Green)
Emergency stop. Feed motor overload.
(6 Red Flashes between Green)
Safety InformationWeak surface. Low clamping force.
(Flashing Green)
Diagnostic InformationDefective control system.
(7 Red Flashes between Green)

Brochures

Make sure you are familiar with Promotech PRO-36 AUTO | Auto Feed Mag Drill brochure including technical data and detailed information about this product. Should you have any further questions we encourage you to send us an enquiry.

Demo video

PRO-36 AUTO | Auto Feed Mag Drill

Join our channels


Technical specification

Motor Speeds350 rpm (under load)
580 rpm (idle run)
Power1020 W
Weight13.5 kg (30 lbs)
Max milling capacity36 mm (1-7/16”)
Max countersinking40 mm (1-9/16”)
Stroke70 mm (2-3/4")
Max depth of cut51 mm (2”)
Voltage1~ 220–240 V, 50–60 Hz
1~ 110–120 V, 50–60 Hz
Magnetic clamping force
(surface with the thickness of 25 mm and roughness Ra = 1.25)
917 kgf (9 000 N)
Magnet Base Dimensions80 mm × 160 mm × 38 mm
3-1/8” × 6-5/16” × 1-1/2”
Min. Workpiece Thickness6 mm (1/4”)
Tool holder19 mm (3/4”) Weldon
Product Code 220–240 V, 50–60 HzWRT-0672-10-20-00-0
Product Code 110–120 V, 50–60 HzWRT-0672-10-10-00-0